- 您现在的位置：买卖IC网 > Sheet目录395 > ATMEGA128RFA1-ZUR (Atmel)IC AVR MCU 2.4GHZ XCEIVER 64QFN
ATmega128
Note:
1. See “About Code Examples” on page 8 .
The receive function example reads all the I/O registers into the register file before any compu-
tation is done. This gives an optimal receive buffer utilization since the buffer location read will
be free to accept new data as early as possible.
Receive Compete Flag
and Interrupt
Receiver Error Flags
The USART Receiver has one flag that indicates the receiver state.
The Receive Complete (RXC) flag indicates if there are unread data present in the receive buf-
fer. This flag is one when unread data exist in the receive buffer, and zero when the receive
buffer is empty (i.e., does not contain any unread data). If the Receiver is disabled (RXEN = 0),
the receive buffer will be flushed and consequently the RXC bit will become zero.
W hen the Receive Complete Interrupt Enable (RXCIE) in UCSRB is set, the USART Receive
Complete Interrupt will be executed as long as the RXC flag is set (provided that global inter-
rupts are enabled). W hen interrupt-driven data reception is used, the receive complete routine
must read the received data from UDR in order to clear the RXC flag, otherwise a new interrupt
will occur once the interrupt routine terminates.
The USART receiver has three error flags: Frame Error (FE), Data OverRun (DOR) and Parity
Error (UPE). All can be accessed by reading UCSRA. Common for the error flags is that they are
located in the receive buffer together with the frame for which they indicate the error status. Due
to the buffering of the error flags, the UCSRA must be read before the receive buffer (UDR),
since reading the UDR I/O location changes the buffer read location. Another equality for the
error flags is that they can not be altered by software doing a write to the flag location. However,
all flags must be set to zero when the UCSRA is written for upward compatibility of future
USART implementations. None of the error flags can generate interrupts.
The Frame Error (FE) flag indicates the state of the first stop bit of the next readable frame
stored in the receive buffer. The FE flag is zero when the stop bit was correctly read (as one),
and the FE flag will be one when the stop bit was incorrect (zero). This flag can be used for
detecting out-of-sync conditions, detecting break conditions and protocol handling. The FE flag
is not affected by the setting of the USBS bit in UCSRC since the receiver ignores all, except for
the first, stop bits. For compatibility with future devices, always set this bit to zero when writing to
UCSRA.
The Data OverRun (DOR) flag indicates data loss due to a receiver buffer full condition. A data
overrun occurs when the receive buffer is full (two characters), it is a new character waiting in
the Receive Shift Register, and a new start bit is detected. If the DOR flag is set there was one
or more serial frame lost between the frame last read from UDR, and the next frame read from
UDR. For compatibility with future devices, always write this bit to zero when writing to UCSRA.
The DOR flag is cleared when the frame received was successfully moved from the Shift Regis-
ter to the receive buffer.
The Parity Error (UPE) flag indicates that the next frame in the receive buffer had a parity error
when received. If parity check is not enabled the UPE bit will always be read zero. For compati-
bility with future devices, always set this bit to zero when writing to UCSRA. For more details see
“Parity Bit Calculation” on page 175 and “Parity Checker” on page 183 .
182
2467X–AVR–06/11
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ATMEGA64RZAPV-10AU
BUNDLE ATMEGA644P/AT86RF230 TQFP
ATP101-TL-H
MOSFET P-CH 30V 25A ATPAK
ATP102-TL-H
MOSFET P-CH 30V 40A ATPAK
ATP103-TL-H
MOSFET P-CH 30V 55A ATPAK
ATP104-TL-H
MOSFET P-CH 30V 75A ATPAK
ATP106-TL-H
MOSFET P-CH 40V 30A ATPAK
ATP107-TL-H
MOSFET P-CH 40V 50A ATPAK
ATP108-TL-H
MOSFET P-CH 40V 70A ATPAK
相关代理商/技术参数
ATMEGA128RFA1-ZUR SL514
制造商:Atmel Corporation 功能描述:
ATMEGA128RFA1-ZUR00
制造商:Atmel Corporation 功能描述:2.4GHZ 802.15.4 128K SOC REVF 制造商:Atmel Corporation 功能描述:2.4GHZ 802.15.4 128K SOC REVF T&R - Bulk 制造商:Atmel from Components Direct 功能描述:ATMEL ATMEGA128RFA1-ZUR00 MICROCONTROLLERS (MCU) 制造商:Atmel 功能描述:Atmel ATMEGA128RFA1-ZUR00 Microcontrollers (MCU) 制造商:Atmel Corporation 功能描述:MCU AVR 2.4GHZ 128K FLASH 64VQFN 制造商:Atmel Corporation 功能描述:2.4GHZ 802.15.4 128K SOC Revision F 制造商:Atmel 功能描述:2.4GHZ 802.15.4 128K SOC REVF
ATMEGA128RFR2-ZF
功能描述:IC RF TXRX+MCU 802.15.4 64-VFQFN 制造商:microchip technology 系列:- 包装:托盘 零件状态:在售 类型:TxRx + MCU 射频系列/标准:802.15.4 协议:Zigbee? 调制:DSSS， O-QPSK 频率:2.4GHz 数据速率（最大值）:2Mbps 功率 - 输出:3.5dBm 灵敏度:-100dBm 存储容量:128kB 闪存，4kB EEPROM，16kB SRAM 串行接口:I2C，JTAG，SPI，USART GPIO:35 电压 - 电源:1.8 V ~ 3.6 V 电流 - 接收:5mA ~ 12.5mA 电流 - 传输:8mA ~ 14.5mA 工作温度:-40°C ~ 125°C 封装/外壳:64-VFQFN 裸露焊盘 标准包装:260
ATMEGA128RFR2-ZU
制造商:Atmel Corporation 功能描述:2.4GHZ 802.15.4 128K SOC IND 85C - Bulk
ATMEGA128RFR2-ZUR
制造商:Atmel Corporation 功能描述:2.4GHZ 802.15.4 128K SOC 85C T&R - Tape and Reel
ATMEGA128RZAV-8AU
功能描述:射频微控制器 - MCU AVR Z-Link Bundle RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:Si100x 数据总线宽度:8 bit 最大时钟频率:24 MHz 程序存储器大小:64 KB 数据 RAM 大小:4 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LGA-42 安装风格:SMD/SMT 封装:Tube
ATMEGA128RZAV-8MU
功能描述:射频微控制器 - MCU AVR Z-Link Bundle RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:Si100x 数据总线宽度:8 bit 最大时钟频率:24 MHz 程序存储器大小:64 KB 数据 RAM 大小:4 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LGA-42 安装风格:SMD/SMT 封装:Tube